**金属饰品镍释放磨损仪、镍释放磨损测试测试仪

2 013年3月1日起，欧盟旧版的镍释放标准EN 1811：1998+A1：2008被新版标准EN 1811：2011替代。

仪器定义：

镍释放量测试仪，也称旋转磨损仪，是一种专门用来打磨金属制品表面的涂层镀层，以达到2年的使用磨损程度的一种辅助仪器。

仪器用途：

该仪器的主要用途是应对欧盟*新的镍释出标准中的镍释放量的辅助检测。

测试方法：

模拟金属制品与人体皮质接触两年的磨损状态，经人工汗液在一定条件下浸泡7天后，配合原子吸收光谱仪定量分析浸泡液中镍的含量，为0.5微克/平方厘米/每周。

适用标准：

EN12472:2005，EN 1811：2011，GB/T28485-2012，ISO24348-2007。

测试范围： 所有饰物，眼镜，手表等金属产品……

仪器优势：

**：触摸屏显示屏，操作简单，显示清晰，极大方便使用者的日常操作！

**：

1：全自动程序控制，能于特定时间转向；

2：当测试完毕，仪器会自动停止。

第三：

清晰LED显示屏显示已运作及剩余时间，让用家更好地分配工作。

第四：安全设计

1：仪器设有保护门及透明观察窗，配合电源及断电保护设计，确保使用安全。

2：配备“暂停”键，让用家能在任何情况下暂时停止仪器运作。

镍释放测试仪专门为EN12472:2005测定涂层覆盖材料镍释放的模拟穿着磨损和腐蚀试验方法标准及ISO 12870:2004眼科光学-眼镜框-要求和测试方法所设计，各项规格均满足上述两项标准要求。

【技术指标】：

1、控制器：**触摸控制。

2、旋转速度：30±2转/分 。

3、承载能力：高性能电机，*大承载能力为10kg，提供稳定转速 。

4、时间设定：可自行设定正转和反转时间 。

5、提醒：任务完成定时提醒功能 。

6、尺寸： 宽：72.0 cm (W) 厚：38.0 cm (D) 高：40.0 cm (H) 。

7、重量： 20 kg 。

8、附件：双层固定支架样品挂具挂架塑料扎带硅橡胶内垫 。

9、其他配置：德国进口磨料（10kg） 德国进口研磨胶（1kg）。

10、电源：AC220V。

一1 第五质量保证事项

一、 本试验机自出厂日期起免费服务期限为一年（消耗品不在免费范围内,不含差旅费）。

二、免费服务之主要凭证

1.请贵公司妥为保存《操作说明书》，如有遗失应于一个月内与我公司客服部联络报备。

2.《操作说明书》若经涂改或未加我公司之印章，则无效。

三、遇下列情况，虽在有效保证期限内，亦得酌收技术或材料费：

1.由于天灾地变而损毁。

2.由于使用者之过失或操作错误以致故障。

3.未按规定使用电源电压导致损坏。

4.自行拆修以致故障。

5.借给他人使用以致故障。

6.自行改装以致故障。

7.自行校正以致故障。

8.转移或运送不慎而故障。

9.远程地区之服务。

Since March 1, 2013, the EU's old version of the nickel release standard, EN 1811:1998+A1:2008, has been replaced by the new standard EN 1811:2011.
Instrument definition:
Nickel release tester, also known as rotary wear tester, is a kind of special coating used to polish the surface of metal products. It can be used as an auxiliary instrument for 2 years.
Instrument use:
The primary use of this instrument is to assist in the detection of the amount of nickel released in the EU's latest nickel release standard.
Test method:
Wear simulation of metal products in contact with the human cortex of two years, the artificial sweat under certain conditions for 7 days, with the analysis of the content in the solution of nickel atomic absorption spectrometry quantitative limit of 0.5 mg / cm2 / week.
Applicable standard:
EN12472:2005, EN, 1811:2011, GB/T28485-2012, ISO24348-2007.
Testing range: all accessories, glasses, watches and other metal products......
Instrument advantage:
First: touch screen display, simple operation, clear display, greatly facilitate the day-to-day operation of the user!
Second:
1: automatic program control, can turn at a certain time;
2: when the test is finished, the instrument will stop automatically.
Third:
The clear LED display shows the operation and remaining time, allowing the user to better distribute the work.
Fourth: safety design
1: instrument with protective door and transparent observation window, with power supply and power failure protection design, to ensure the safe use.
2: equipped with the "pause" button, so that the user can in any case temporarily stop the instrument operation.
For the EN12472:2005 determination of nickel release coating covering material of nickel release tester in simulation wear and corrosion test method standard and ISO 12870:2004 ophthalmic optics - spectacle frame - Requirements and test methods for the design specifications meet the requirements of the two standards.
[technical indicators]:
1: Controller: advanced touch control.
2, rotating speed: 30 + 2 revolutions / min..
3, carrying capacity: high performance motor, the maximum carrying capacity of 10kg, providing stable speed.
4, time setting: you can set the forward and reverse timing.
5: reminder: task completion, timing reminder function.
6, size: width: 72 cm (W) thickness: 38 cm (D) high: 40 cm (H).
7, weight: 20 kg.
8, annex: double fixation rack rack sample plastic ribbon silicon rubber pad.
9, other configurations: Germany imported abrasives (10kg), Germany imported abrasives (1kg).
10, power: AC220V.
One, 1, fifth quality assurance matters
First, the test machine from the factory date of free service for one year (consumables are not within the scope of free, excluding travel expenses).
Two, the main vouchers for free services
1.. Please keep the operation instruction properly. If lost, please contact our customer service department within one month.
2. "operating instructions" if altered or not seal our company, is invalid.
Three, in the following circumstances, although in the effective guarantee period, also have to receive technical or material costs:
1. because of natural disaster damage.
2. failure due to user's fault or operation error.
3. failure to use the supply voltage leads to damage.
4. self repair, so that failure.
5. lend to others for use so as to fail.
6. self modification so as to malfunction.
7. self correcting so as to malfunction.
8. transfer or transport inadvertent failure.
9. services in remote areas.